My Bremont ALT1-C Anthrachite

My Bremont ALT1-C in front of DMC-CA

I have mentioned that I have a liking to Bremont watches, I even made a 3D model of one.  After months of research, I was able to acquire an ALT1-C.    About a month ago, I found one on eBay and pulled the trigger.  The watch was previously owned, but in great condition...a few minor scratches, nothing I would not eventually put there myself, as I have a history of running into things with my wrist.  The watch was recently serviced by Bremont and had a new bezel.  Basically, it was a 'new' watch.  Lucky for me, the auction was to close on a holiday weekend.  This meant, in theory, that others looking at the auction were too busy partying and not paying attention to the auction.  You snooze, you lose...more like...you party, you no get watchy for less than half price of retaily.

Watch with strap options

While the watch itself was in great condition, the strap that it came with was only in 'good' condition.  It came with a standard black leather strap with white stitching on a traditional buckle closure.  Strap can be seen in upper left in image above

I should note that this is an older model with 'old logo' and 'Swiss Made' on the dial.  Newer Bremont's have an updated logo and "London" on the dial.  Anyway, I wanted the deployant clasp for my watch.  It just happened that one was being sold by a member of  the ALT1TUDE Bremont forum.  He also had a new strap, black leather with red stitching, and gave me a good deal on both.  See image.

On the right side of the image is Bremont's NATO strap.  I got this from another member of ALT1TUDE. Now, I have options for every occasion.  Well, I do not have the metal bracelet, yet.

Remember that 3D model I made?  Here are some images for comparison.

Comparing 3D model to real thing

Nothing wrong with your monitor, the 3D model is slightly bigger.  For some reason it came out bigger than what I thought I measured. My model and/or print out came out about 2% larger.  Better that the real watch is smaller than I thought.  That way, when I wear my Bremont, it does not make my wrist look too small.  No worries, I can always adjust some number and print out another, more accurate, version.  You know...for research.

Back of 3D mode and ALT1-C

If you look closely at the lugs, you can see that the 3D model on the left is a little bulkier that it should be.  On the right the lugs are way more sexier.  The movement and rotor look pretty good, but the one on the right keeps better time. 

Analyzing the NATO straps

As you recall, I made a NATO strap from a convention lanyard.  I did not have great photos of this strap, but made my best guess.  As far as construction, I pretty much got it.  I do not have the velvet like lining for the back of watch (between the spring bars) and back of strap, due to lack of reference. 

Stunt double

Of course, the quality of the materials and construction of my band is no where near the quality of the Bremont strap.  My strap is also a little longer that it should be.  When it sits on my wrist, it is too loose.  The Bremont strap fits perfect.

There you have it, my first Bremont.

Bremont ALT1-C Anthracite

My Obsession with Bremont Watches

Bremont Chronometers

I have always had a passion for watches...pretty much all time machines.  A few months ago, I was shopping for watches and came upon some lesser known brands (at least to me).  One of these brands is Bremont.  From a design and aesthetic perspective, these watches are wonderfully crafted.  Their design is inspired by aviation, as their founders Nick and Giles English are pilots themselves.  I also have a passion for aviation that dates back to movies like Top Gun, which started my love for military planes.  Bremont collaborates with military squadrons to create exclusive watches, as well as other limited edition watches like the Victory, Wright Flyer, Codebreaker, and many more.

Bremont's story is amazing, it is one of the reasons why fell in love with this brand.  While they are fairly new to the watch market, founded in 2002, they have made a huge impact in the industry in a short time.  All their watches are hand built in England and are all COSC certified.

Bremont Alt1-C Anthracite

So, it is decided that my next watch is going to be a Bremont Alt1-C.  Since learning about Bremont, I have been learning about their watches and the company itself.  One weekend, I went to check out these watches in the only Authorized Dealer of Bremont within 275 miles.  Boy, pictures do not do these watches justice.  Once you see a Bremont (and I guess any luxury watch) in person, you realise the work that goes into to them. 

Technical drawing of Bremont watch

The Bremont website has this wonderful technical drawing of their watch. Technical drawings like these have a special place in my heart, I used to spend hours making these types of drawings...for fun.  All their watches follow these basic measurements.  While there are some variations in case diameter, over 95% of their line uses the same 43mm case.  The detail drawings gave me an idea to make one. Hey, it is what I do, I make things to fill the voids in my life.

Solid buck

This was made before I saw the real watches.  My only references to Bremont watches are from internet images and videos.  Since I had yet to see one, I wanted to see what the size was in three-dimensions.   While I have watches ranging from different sizes, you really do not know how a watch really 'fits' you, until you put it on.  At 43mm, hopefully it does not make my dainty wrist look even smaller.  The first version I made is a solid buck.  This was made one-to-one so I can see how it would sit on my wrist.

Bremont's NATO strap with red stiching

Speaking of wrist, I need a band for the watch.  Since I do not leather around, the traditional leather strap is out.  A leather strap would also require a buckle or clasp system that would need to be made.  Although, I do love that deployant clasp, perhaps some other time.  A bracelet woulds also need extensive fabrication.  A simple strap to make is Bremont's NATO strap.  So, I copied the NATO strap...using a lanyard.

Printout of watch and making of NATO strap

I studied the images of the strap and made my best guess on how it was constructed.  Made some initial sketches and measurements and off I go.  Luckily, the lanyard I found was pretty darn close to the 22mm width.  The length of the strap was just eyeballed as the real strap is one size fits all.

Strap was hand sewn.

The lanyard I used is obviously not as tough or thick as the nylon used on the NATO strap.  It is just a cheap give away lanyard they hand out at conventions.  Instead of leather keepers, I am also using the same nylon. The loop was made from cut styrene. I had some hook-and-loop strips laying around and stuck them on the strap, sewing the ends. 

So, what is next?  A solid buck will not do. Sure it gave me a great idea of size.  But, I have to take it up a notch.  One of the unique features of a Bremont is their Trip-Tick® Case Design.  Basically, a three piece construction consisting of a top bezel, center barrel, and case back.  Time to part out the buck I made and make a Trip-Tick® like construction.

Exploded parts - top

While I was at it, I wanted to separate the crystal pieces and have them printed out in clear to see the dial and movement.

Explode parts - bottom

Oh, heck.  Why not get the rotor in there as a separate piece?  We have a window, why not see the rotor?  This is a seven piece construction:  top crystal, bezel, barrel, dial/movement, rotor, case back, back crystal.

Exploded view of Bremont's Martin Baker Series

I combined a lot of pieces together for ease of modeling, printing and clean up.  The image above shows a more detailed exploded view of a Bremont watch.  Even this illustration is simplified as the hands, movement, rotor, etc., have been combined.

Layout of markers and image planes

Most of the work was getting the details of the face.  I am limited to the resolution of the printers so some parts, like the hands. had to be drafted to the face of the watch. The lettering, numbers, and logos are raised instead of painting these on.  This meant I needed to recreate the graphics in order to sculpt them in relief .

Detail of watch face

Since the hands do not move, they are sculpted in the the beauty pose as seen in the top image of watch.  The hands are drafted to the face for ease of printing.

Layout of movement and image planes

On the back, I tried to get as much of the movement detail as possible.  Again, due to the resolution of the printers, I opted out of sculpted each tooth on the gears and omitted some of the smaller details. These details would not print and/or would break during clean up.  Instead of teethed gears, they are represented with discs of the same diameter.  Some spring details were also omitted.

Detail of movement with rotor

The rotor is a separate piece so it can be pinned, allowing it to rotate.  This will be seen through the back crystal.

Enough of the screen shots, you probably want to see the print outs.

Print outs

The clear pieces are not super clear, but it is good enough as you can still see into the dial and movement.  On to assembly.  The tolerances are super tight on this, so there was some minor sanding involved to get the parts to fit.

Assembly of parts

The crystal pieces are pressed in and held by friction.  A pin is pressed into the movement piece for the rotor to spin on.  The build lines of the print out makes the surfaces a bit rough, so the rotor does not turn as smoothly as I would like.  Even after greasing the area, it still tends to stick a bit.

Trip-Tick® Case Design

The dial/movement piece was press fitted into the barrel piece. This was a real tight fit.  There was quite a bit of sanding and testing before I could press the piece into the barrel.  I do not think I can even pop it back out without damaging either piece.  At least now, I have the three main pieces of the Trip-Tick® represented.

Close up of movement detail with case back removed

The three main pieces lock into place with friction as well as mortises and tenons I sculpted into the pieces.  The holes and pins follow the five point pattern of where the screws would be on the real watch.

Assembled - back

Had I more knowledge of how a watch movement works, I may have made this work.  Okay, not really.  The material is not strong enough for that.  But, as you can see it does not look too bad.

Assembled - front

The crown and buttons were sculpted to be part of the barrel for ease of print and assembly. They would not have been able to 'adjust' watch or 'activate' the chronograph, anyway.  I also omitted the flutes on the crown.

Both versions of Bremont watch and NATO strap

I used styrene rods to represent the spring bars.  These are just forced in the little dimples on the lugs, held on by tension.  No springs were used.  You can also see the completed strap.  I even tried to replicate the stitched triangles on the straps.

So there you have it.  Not sure what I am going to do with these.  Although, I do admit, I have been wearing it around to get the feel of the size.  The weight is totally off, since there is no weight information at the time and the material used is fairly light.  Perhaps I will make other Bremont models like the Martin Baker or models that will be nearly impossible for me to acquire like the Codebreaker, P-51, or EP120.

Maybe I should bring these to the watch dealer the next time I go.  Hopefully, I will leave the dealer with a real Bremont Alt1-C.